Cummins fault code 1881
DPF Differential Pressure Sensor Circuit: circuit voltage low / shorted low
What it means
Cummins' description: Aftertreatment Diesel Particulate Filter Differential Pressure Sensor Circuit - Voltage below normal.
SPN 3251 is Aftertreatment 1 Diesel Particulate Filter Differential Pressure. FMI 4 means the voltage on the circuit is lower than possible for a good sensor, usually a short to ground, a damaged harness, or a failed sensor.
The DPF traps soot from the exhaust and burns it off during regeneration. Pressure and temperature sensors before and after the filter tell the ECM how loaded the filter is and whether regeneration is working.
What the lamp means
An amber (yellow) warning lamp means the engine can usually keep running, but the fault should be repaired soon, ideally the same day.
Green, yellow, red: three ways this can look
The same code can be a quick fix or a reason to shut down. Match your situation to the closest example.
Keep an eye on it
The DPF lamp comes on solid and the truck drives normally. Running it at highway speed for 20-30 minutes, or doing a parked regen if your truck supports it, clears it.
Schedule a repair
The DPF lamp is flashing or the code keeps coming back after regens. Plan service soon. The filter is loading faster than it can clean itself and something upstream may be wrong.
Stop and get help
Stop lamp on, power derated, or a strong exhaust smell or smoke. Don't keep driving. A plugged DPF can overheat, crack, and take the turbo or engine with it.
Common causes
FMI 4 is an electrical or signal fault, so start with the circuit:
- Cracked, melted or disconnected sensor hose (common on differential pressure sensors)
- Damaged connector or chafed harness near the hot exhaust
- Failed pressure or temperature sensor
- Sensor module or 5-volt supply problem
If the circuit checks out, the reading may be real. Other possibilities: too much idling or short trips, so the DPF never gets hot enough to regenerate; regeneration interrupted or inhibited (inhibit switch on, key-off mid regen); upstream problem making excess soot: leaking injector, EGR or boost fault.
What you can check before calling
- Check the dash for a regen or DPF lamp and whether a regen is being requested
- Make sure the regen inhibit switch isn't turned on
- Look at the sensor hoses and wiring on top of the DPF for melted or loose lines
- Note how much the truck idles versus runs at highway speed
Clearing the code without fixing the cause usually brings it right back, and on emissions systems it can restart derate timers. For the bigger picture, read our guide: DPF regeneration explained: passive, active and forced.
Engines and sources
Listed by Cummins for: QSB 6.7 (DOC/ DPF+ SCR), QSL 9 (DOC/ DPF+ SCR), QSX 15, QSG 12. Cummins uses the same fault code numbers across its electronic engines, including on-highway models like the ISB/B6.7, ISL/L9 and ISX/X15, though not every code applies to every engine or software level. Source: Cummins Tier 4 Fault Codes. Always confirm with Cummins service information (QuickServe) for your engine serial number.
Same SPN, other failure types
- 1879 SPN 3251 FMI 3
DPF Differential Pressure Sensor Circuit: circuit voltage high / shorted high - 1883 SPN 3251 FMI 2
DPF Differential Pressure Sensor: erratic or intermittent signal - 1921 SPN 3251 FMI 16
DPF Differential Pressure: reading above normal (moderately severe) - 1922 SPN 3251 FMI 0
DPF Differential Pressure: reading above normal (most severe) - 2639 SPN 3251 FMI 15
DPF Differential Pressure: reading above normal (least severe)
Related DPF codes
- 1981 SPN 3936 FMI 15
DPF System: reading above normal (least severe) - 1993 SPN 4795 FMI 31
DPF Missing: condition exists - 2742 SPN 3249 FMI 17
Exhaust Gas Temperature 2: reading below normal (least severe) - 2743 SPN 3249 FMI 18
Exhaust Gas Temperature 2: reading below normal (moderately severe) - 2754 SPN 81 FMI 16
Engine DPF Intake Pressure: reading above normal (moderately severe) - 2777 SPN 3703 FMI 31
Particulate Trap Active Regeneration Inhibited Due to Inhibit Switch: condition exists
Look up another code
Cummins fault code (like 1922), J1939 SPN and FMI (like SPN 3251 FMI 0), or an OBD-II code (like P0420).
Questions
What does Cummins fault code 1881 mean?
Cummins fault code 1881 is J1939 SPN 3251 FMI 4: Aftertreatment Diesel Particulate Filter Differential Pressure Sensor Circuit - Voltage below normal. In plain terms: dpf differential pressure sensor circuit: circuit voltage low / shorted low.
Can I keep driving with Cummins code 1881?
Usually for a short time, if the engine runs normally and no other warnings are on. Get it diagnosed soon, because many amber codes lead to a derate if ignored. Look at the green, yellow and red examples on this page to judge your situation.
What is the SPN and FMI for Cummins code 1881?
SPN 3251 identifies the part or system (Aftertreatment 1 Diesel Particulate Filter Differential Pressure). FMI 4 describes the type of failure: circuit voltage low / shorted low.
What usually causes Cummins code 1881?
The most common causes are: cracked, melted or disconnected sensor hose (common on differential pressure sensors); damaged connector or chafed harness near the hot exhaust; failed pressure or temperature sensor.
Diesel down in the Midlands?
We work on Cummins-powered pickups, vans and medium-duty trucks across Lexington, Columbia and the Midlands, on site at your yard or roadside.