Cummins fault code 2322
Engine Camshaft Speed / Position Sensor: erratic or intermittent signal
What it means
Cummins' description: Engine Camshaft Speed / Position Sensor - Data erratic, intermittent or incorrect.
SPN 723 is Engine Speed 2. FMI 2 means the signal is jumping around, dropping in and out, or doesn't make sense compared to other readings.
The crank and cam position sensors tell the ECM exactly where each piston is so it can time fuel injection. Losing one causes rough running; losing both usually stops the engine.
What the lamp means
This code normally doesn't turn on a dash lamp. It's logged in the ECM for a technician to see, and often explains another active code.
Green, yellow, red: three ways this can look
The same code can be a quick fix or a reason to shut down. Match your situation to the closest example.
Keep an eye on it
One sensor code that set briefly and cleared, with the engine starting and running normally.
Schedule a repair
Long cranking, occasional stalling, or the code returns. Replace the sensor soon. These usually fail completely without much warning.
Stop and get help
Engine stalls or won't start, or a stop lamp with lost speed signals. Don't plan on driving it until it's fixed.
Common causes
The sensor reading itself is out of range or the condition is real, so look at the system:
- Real engine overspeed from downhill or a missed shift
- Signal noise from aftermarket electrical add-ons
What you can check before calling
- Note any stalling, hard starting, or rough running
- Look at the sensor connectors for oil or damage
- Think about whether any electrical work was done recently
Clearing the code without fixing the cause usually brings it right back, and on emissions systems it can restart derate timers.
Engines and sources
Listed by Cummins for: QSB 6.7, QSL 9, QSX 15, QSB 4.5, QSF 3.8, QSG 12. Cummins uses the same fault code numbers across its electronic engines, including on-highway models like the ISB/B6.7, ISL/L9 and ISX/X15, though not every code applies to every engine or software level. Source: Cummins Tier 4 Fault Codes. Always confirm with Cummins service information (QuickServe) for your engine serial number.
Same SPN, other failure types
Related Engine speed and position sensors codes
- 2321 SPN 190 FMI 2
Engine Crankshaft Speed/Position: erratic or intermittent signal - 2468 SPN 190 FMI 16
Engine Crankshaft Speed/Position: reading above normal (moderately severe) - 1992 SPN 190 FMI 16
Engine Crankshaft Speed/Position: reading above normal (moderately severe) - 689 SPN 190 FMI 2
Engine Crankshaft Speed/Position: erratic or intermittent signal - 523 SPN 611 FMI 2
Auxiliary Intermediate (PTO) Speed Switch Validation: erratic or intermittent signal - 497 SPN 1377 FMI 2
Multiple Unit Synchronization Switch: erratic or intermittent signal
Look up another code
Cummins fault code (like 1922), J1939 SPN and FMI (like SPN 3251 FMI 0), or an OBD-II code (like P0420).
Questions
What does Cummins fault code 2322 mean?
Cummins fault code 2322 is J1939 SPN 723 FMI 2: Engine Camshaft Speed / Position Sensor - Data erratic, intermittent or incorrect. In plain terms: engine camshaft speed / position sensor: erratic or intermittent signal.
Can I keep driving with Cummins code 2322?
Usually, yes. This code doesn't normally turn on a lamp by itself, but check for other active codes that might be more serious. Look at the green, yellow and red examples on this page to judge your situation.
What is the SPN and FMI for Cummins code 2322?
SPN 723 identifies the part or system (Engine Speed 2). FMI 2 describes the type of failure: erratic or intermittent signal.
What usually causes Cummins code 2322?
The most common causes are: real engine overspeed from downhill or a missed shift; signal noise from aftermarket electrical add-ons.
Diesel down in the Midlands?
We work on Cummins-powered pickups, vans and medium-duty trucks across Lexington, Columbia and the Midlands, on site at your yard or roadside.