Cummins fault code 2571
Engine Charge Air Cooler Outlet Temperature: circuit voltage high / shorted high
What it means
Cummins' description: Engine Charge Air Cooler Outlet Temperature - Voltage above normal, or shorted to high source.
SPN 2630 is Engine Charge Air Cooler 1 Outlet Temperature. FMI 3 means the voltage on the circuit is higher than possible for a good sensor, usually an open signal wire, a short to a power wire, or a failed sensor.
These sensors measure the air coming into the engine: intake manifold temperature, charge air cooler outlet temperature, ambient temperature, barometric pressure, humidity and air filter restriction. The ECM uses them to calculate fueling and timing.
What the lamp means
An amber (yellow) warning lamp means the engine can usually keep running, but the fault should be repaired soon, ideally the same day.
Green, yellow, red: three ways this can look
The same code can be a quick fix or a reason to shut down. Match your situation to the closest example.
Keep an eye on it
A one-time sensor code with normal power and temperatures.
Schedule a repair
Amber lamp, rough cold starts, or the code returns. Usually a sensor or connector. Book it so fueling stays correct.
Stop and get help
Several sensor codes at once with a stop lamp or no-start. That can point to a shared sensor supply or ECM problem. Get it diagnosed before driving.
Common causes
FMI 3 is an electrical or signal fault, so start with the circuit:
- Sensor connector corroded or loose
- Harness damage
- Failed sensor
- Shared 5-volt sensor supply problem (several sensor codes at once)
If the circuit checks out, the reading may be real. Other possibilities: clogged air filter; dirty or blocked charge air cooler or radiator fins; real high intake temperature in hot weather or under heavy load.
What you can check before calling
- Check the air filter and the restriction indicator
- Clean bugs and debris from the front of the charge air cooler
- Look for unplugged or damaged connectors on intake sensors
Clearing the code without fixing the cause usually brings it right back, and on emissions systems it can restart derate timers.
Engines and sources
Listed by Cummins for: QSB 6.7, QSL 9, QSX 15, QSF 3.8, QSG 12. Cummins uses the same fault code numbers across its electronic engines, including on-highway models like the ISB/B6.7, ISL/L9 and ISX/X15, though not every code applies to every engine or software level. Source: Cummins Tier 4 Fault Codes. Always confirm with Cummins service information (QuickServe) for your engine serial number.
Same SPN, other failure types
Related Intake air and environment sensors codes
- 2398 SPN 171 FMI 2
Ambient Air Temperature: erratic or intermittent signal - 2964 SPN 105 FMI 15
Intake Manifold 1 Temperature: reading above normal (least severe) - 1943 SPN 3555 FMI 17
Ambient Air Density: reading below normal (least severe) - 3341 SPN 107 FMI 16
Engine Air Filter Differential Pressure: reading above normal (moderately severe) - 3367 SPN 4490 FMI 9
Specific Humidity Sensor: abnormal update rate - 3385 SPN 105 FMI 18
Intake Manifold 1 Temperature: reading below normal (moderately severe)
Look up another code
Cummins fault code (like 1922), J1939 SPN and FMI (like SPN 3251 FMI 0), or an OBD-II code (like P0420).
Questions
What does Cummins fault code 2571 mean?
Cummins fault code 2571 is J1939 SPN 2630 FMI 3: Engine Charge Air Cooler Outlet Temperature - Voltage above normal, or shorted to high source. In plain terms: engine charge air cooler outlet temperature: circuit voltage high / shorted high.
Can I keep driving with Cummins code 2571?
Usually for a short time, if the engine runs normally and no other warnings are on. Get it diagnosed soon, because many amber codes lead to a derate if ignored. Look at the green, yellow and red examples on this page to judge your situation.
What is the SPN and FMI for Cummins code 2571?
SPN 2630 identifies the part or system (Engine Charge Air Cooler 1 Outlet Temperature). FMI 3 describes the type of failure: circuit voltage high / shorted high.
What usually causes Cummins code 2571?
The most common causes are: sensor connector corroded or loose; harness damage; failed sensor.
Diesel down in the Midlands?
We work on Cummins-powered pickups, vans and medium-duty trucks across Lexington, Columbia and the Midlands, on site at your yard or roadside.